RTJ Face Dimensions and Flange Tolerances
RTJ Ring Number & Gasket Lookup
Pick the pressure class and size of a ring type joint (RTJ) flange to get its R-series ring gasket number, the groove dimensions (pitch diameter P, depth E, width F, bottom radius R) and the raised-portion diameter K. You can also enter a ring number to see which flange sizes and classes use it, or enter a measured groove pitch diameter to find the ring. Values come from the RTJ face dimensions chart below for ASME B16.5 flanges.
4" Class 300 RTJ flange
R37 ring gasket
(8) studs, 3/4-10 UNC × 5 in (RTJ length)
- Pitch diameter P
- 5-7/8 in
- Groove depth E
- 5/16 in
- Groove width F
- 15/32 in
- Bottom radius R
- 1/32 in
- Raised portion diameter K (Class 300)
- 6-7/8 in
- Used on
- 4" Class 300, 4" Class 400, 4" Class 600, 4" Class 900
The ring pitch diameter equals the groove pitch diameter P. Ring cross-section dimensions, ring hardness and other gasket types are not on this chart. Ask Texas Flange sales for ring gaskets to your specification.
Reference tool for planning and quoting. Confirm against the purchase specification and your site's procedures before use.
Request a flange quote| Nominal Pipe Size | Groove Dimensions | Diameter of Raised Portion K | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Class 150 | Class 300 | Class 400 | Class 600 | Class 900 | Class 1500 | Class 2500 | Groove # | Pitch Dia | Depth | Width | Radius at Bottom | Class 150 | Class 300 / 400 / 600 | Class 900 | Class 1500 | Class 2500 | Depth |
| P | E | F | R | E | |||||||||||||
| – | 1/2 | – | 1/2 | – | – | – | R11 | 1-11/32 | 7/32 | 9/32 | 1/32 | – | 2 | – | – | – | 7/32 |
| – | – | – | – | – | 1/2 | – | R12 | 1-9/16 | 1/4 | 11/32 | 1/32 | – | – | 2-3/8 | 2-3/8 | – | 1/4 |
| – | 3/4 | – | 3/4 | – | – | 1/2 | R13 | 1-11/16 | 1/4 | 11/32 | 1/32 | – | 2-1/2 | – | – | 2-9/16 | 1/4 |
| – | – | – | – | – | 3/4 | – | R14 | 1-3/4 | 1/4 | 11/32 | 1/32 | – | – | 2-5/8 | 2-5/8 | – | 1/4 |
| 1 | – | – | – | – | – | – | R15 | 1-7/8 | 1/4 | 11/32 | 1/32 | 2-1/2 | – | – | – | – | 1/4 |
| – | 1 | – | 1 | – | 1 | 3/4 | R16 | 2 | 1/4 | 11/32 | 1/32 | – | 2-3/4 | 2-13/16 | 2-13/16 | 2-7/8 | 1/4 |
| 1-1/4 | – | – | – | – | – | – | R17 | 2-1/4 | 1/4 | 11/32 | 1/32 | 2-7/8 | – | – | – | – | 1/4 |
| – | 1-1/4 | – | 1-1/4 | – | 1-1/4 | 1 | R18 | 2-3/8 | 1/4 | 11/32 | 1/32 | – | 3-1/8 | 3-3/16 | 3-3/16 | 3-1/4 | 1/4 |
| 1-1/2 | – | – | – | – | – | – | R19 | 2-9/16 | 1/4 | 11/32 | 1/32 | 3-1/4 | – | – | – | – | 1/4 |
| – | 1-1/2 | – | 1-1/2 | – | 1-1/2 | – | R20 | 2-11/16 | 1/4 | 11/32 | 1/32 | – | 3-9/16 | 3-5/8 | 3-5/8 | – | 1/4 |
| – | – | – | – | – | – | 1-1/4 | R21 | 2-27/32 | 5/16 | 15/32 | 1/32 | – | – | – | – | 4 | 5/16 |
| 2 | – | – | – | – | – | – | R22 | 3-1/4 | 1/4 | 11/32 | 1/32 | 4 | – | – | – | – | 1/4 |
| – | 2 | – | 2 | – | – | 1-1/2 | R23 | 3-1/4 | 5/16 | 15/32 | 1/32 | – | 4-1/4 | – | – | 4-1/2 | 5/16 |
| – | – | – | – | – | 2 | – | R24 | 3-3/4 | 5/16 | 15/32 | 1/32 | – | – | 4-7/8 | 4-7/8 | – | 5/16 |
| 2-1/2 | – | – | – | – | – | – | R25 | 4 | 1/4 | 11/32 | 1/32 | 4-3/4 | – | – | – | – | 1/4 |
| – | 2-1/2 | – | 2-1/2 | – | – | 2 | R26 | 4 | 5/16 | 15/32 | 1/32 | – | 5 | – | – | 5-1/4 | 5/16 |
| – | – | – | – | – | 2-1/2 | – | R27 | 4-1/4 | 5/16 | 15/32 | 1/32 | – | – | – | 5-3/8 | – | 5/16 |
| – | – | – | – | – | – | 2-1/2 | R28 | 4-3/8 | 3/8 | 17/32 | 1/16 | – | – | – | – | 5-7/8 | 3/8 |
| 3 | – | – | – | – | – | – | R29 | 4-1/2 | 1/4 | 11/32 | 1/32 | 5-1/4 | – | – | – | – | 1/4 |
| – | – | – | – | – | – | – | R30 | 4-5/8 | 5/16 | 15/32 | 1/32 | – | – | – | – | – | 5/16 |
| – | 3 | – | 3 | 3 | – | – | R31 | 4-7/8 | 5/16 | 15/32 | 1/32 | – | 5-3/4 | 6-1/8 | – | – | 5/16 |
| – | – | – | – | – | – | 3 | R32 | 5 | 3/8 | 17/32 | 1/16 | – | – | – | – | 6-5/8 | 3/8 |
| 3-1/2 | – | – | – | – | – | – | R33 | 5-3/16 | 1/4 | 11/32 | 1/32 | 6-1/16 | – | – | – | – | 1/4 |
| – | 3-1/2 | – | 3-1/2 | – | – | – | R34 | 5-3/16 | 5/16 | 15/32 | 1/32 | – | 6-1/4 | – | – | – | 5/16 |
| – | – | – | – | – | 3 | – | R35 | 5-3/8 | 5/16 | 15/32 | 1/32 | – | – | – | 6-5/8 | – | 5/16 |
| 4 | – | – | – | – | – | – | R36 | 5-7/8 | 1/4 | 11/32 | 1/32 | 6-3/4 | – | – | – | – | 1/4 |
| – | 4 | 4 | 4 | 4 | – | – | R37 | 5-7/8 | 5/16 | 15/32 | 1/32 | – | 6-7/8 | 7-1/8 | – | – | 5/16 |
| – | – | – | – | – | – | 4 | R38 | 6-3/16 | 7/16 | 21/32 | 1/16 | – | – | – | – | 8 | 7/16 |
| – | – | – | – | – | 4 | – | R39 | 6-3/8 | 5/16 | 15/32 | 1/32 | – | – | – | 7-5/8 | – | 5/16 |
| 5 | – | – | – | – | – | – | R40 | 6-3/4 | 1/4 | 11/32 | 1/32 | 7-5/8 | – | – | – | – | 1/4 |
| – | 5 | 5 | 5 | 5 | – | – | R41 | 7-1/8 | 5/16 | 15/32 | 1/32 | – | 8-1/4 | 8-1/2 | – | – | 5/16 |
| – | – | – | – | – | – | 5 | R42 | 7-1/2 | 1/2 | 25/32 | 1/16 | – | – | – | 9-1/2 | 1/2 | |
| 6 | – | – | – | – | – | – | R43 | 7-5/8 | 1/4 | 11/32 | 1/32 | 8-5/8 | – | – | – | – | 1/4 |
| – | – | – | – | – | 5 | – | R44 | 7-5/8 | 5/16 | 15/32 | 1/32 | – | – | – | 9 | – | 5/16 |
| – | 6 | 6 | 6 | 6 | – | – | R45 | 8-5/16 | 5/16 | 15/32 | 1/32 | – | 9-1/2 | 9-1/2 | – | – | 5/16 |
| Nominal Pipe Size | Groove Dimensions | Diameter of Raised Portion K | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Class 150 | Class 300 | Class 400 | Class 600 | Class 900 | Class 1500 | Class 2500 | Groove # | Pitch Dia | Depth | Width | Radius at Bottom | Class 150 | Class 300 / 400 / 600 | Class 900 | Class 1500 | Class 2500 | Depth |
| P | E | F | R | E | |||||||||||||
| – | – | – | – | – | 6 | – | R46 | 8-5/16 | 3/8 | 17/32 | 1/16 | – | – | – | 9-3/4 | – | 3/8 |
| – | – | – | – | – | – | 6 | R47 | 9 | 1/2 | 25/32 | 1/16 | – | – | – | – | 11 | 1/2 |
| 8 | – | – | – | – | – | – | R48 | 9-3/4 | 1/4 | 11/32 | 1/32 | 10-3/4 | – | – | – | – | 1/4 |
| – | 8 | 8 | 8 | 8 | – | – | R49 | 10-5/8 | 5/16 | 15/32 | 1/32 | – | 11-7/8 | 12-1/8 | – | – | 5/16 |
| – | – | – | – | – | 8 | – | R50 | 10-5/8 | 7/16 | 21/32 | 1/16 | – | – | – | 12-1/2 | – | 7/16 |
| – | – | – | – | – | – | 8 | R51 | 11 | 9/16 | 29/32 | 1/16 | – | – | – | – | 13-3/8 | 9/16 |
| 10 | – | – | – | – | – | – | R52 | 12 | 1/4 | 11/32 | 1/32 | 13 | – | – | – | – | 1/4 |
| – | 10 | 10 | 10 | 10 | – | – | R53 | 12-3/4 | 5/16 | 15/32 | 1/32 | – | 14 | 14-1/4 | – | – | 5/16 |
| – | – | – | – | – | 10 | – | R54 | 12-3/4 | 7/16 | 21/32 | 1/16 | – | – | – | 14-5/8 | – | 7/16 |
| – | – | – | – | – | – | 10 | R55 | 13-1/2 | 11/16 | 1-3/16 | 3/32 | – | – | – | – | 16-3/4 | 11/16 |
| 12 | – | – | – | – | – | – | R56 | 15 | 1/4 | 11/32 | 1/32 | 16 | – | – | – | – | 1/4 |
| – | 12 | 12 | 12 | 12 | – | – | R57 | 15 | 5/16 | 15/32 | 1/32 | – | 16-1/4 | 16-1/2 | – | – | 5/16 |
| – | – | – | – | – | 12 | – | R58 | 15 | 9/16 | 29/32 | 1/16 | – | – | – | 17-1/4 | – | 9/16 |
| 14 | – | – | – | – | – | – | R59 | 15-5/8 | 1/4 | 11/32 | 1/32 | 16-3/4 | – | – | – | – | 1/4 |
| – | – | – | – | – | – | 12 | R60 | 16 | 11/16 | 1-5/16 | 3/32 | – | – | – | – | 19-1/2 | 11/16 |
| – | 14 | 14 | 14 | – | – | – | R61 | 16-1/2 | 5/16 | 15/32 | 1/32 | – | 18 | – | – | – | 5/16 |
| – | – | – | – | 14 | – | – | R62 | 16-1/2 | 7/16 | 21/32 | 1/16 | – | – | 18-3/8 | – | – | 7/16 |
| – | – | – | – | – | 14 | – | R63 | 16-1/2 | 5/8 | 1-1/16 | 3/32 | – | – | – | 19-1/4 | – | 5/8 |
| 16 | – | – | – | – | – | – | R64 | 17-7/8 | 1/4 | 11/32 | 1/32 | 19 | – | – | – | – | 1/4 |
| – | 16 | 16 | 16 | – | – | – | R65 | 18-1/2 | 5/16 | 15/32 | 1/32 | – | 20 | – | – | – | 5/16 |
| – | – | – | – | 16 | – | – | R66 | 18-1/2 | 7/16 | 21/32 | 1/16 | – | – | 20-5/8 | – | – | 7/16 |
| – | – | – | – | – | 16 | – | R67 | 18-1/2 | 11/16 | 1-3/16 | 3/32 | – | – | – | 21-1/2 | – | 11/16 |
| 18 | – | – | – | – | – | – | R68 | 20-3/8 | 1/4 | 11/32 | 1/32 | 21-1/2 | – | – | – | – | 1/4 |
| – | 18 | 18 | 18 | – | – | – | R69 | 21 | 5/16 | 15/32 | 1/32 | – | 22-5/8 | – | – | – | 5/16 |
| – | – | – | – | 18 | – | – | R70 | 21 | 1/2 | 25/32 | 1/16 | – | – | 23-3/8 | – | – | 1/2 |
| – | – | – | – | – | 18 | – | R71 | 21 | 11/16 | 1-3/16 | 3/32 | – | – | – | 24-1/8 | – | 11/16 |
| 20 | – | – | – | – | – | – | R72 | 22 | 1/4 | 11/32 | 1/32 | 23-1/2 | – | – | – | – | 1/4 |
| – | 20 | 20 | 20 | – | – | – | R73 | 23 | 3/8 | 17/32 | 1/16 | – | 25 | – | – | – | 3/8 |
| – | – | – | – | 20 | – | – | R74 | 23 | 1/2 | 25/32 | 1/16 | – | – | 25-1/2 | – | – | 1/2 |
| – | – | – | – | – | 20 | – | R75 | 23 | 11/16 | 1-5/16 | 3/32 | – | – | – | 26-1/2 | – | 11/16 |
| 24 | – | – | – | – | – | – | R76 | 26-1/2 | 1/4 | 11/32 | 1/32 | 28 | – | – | – | – | 1/4 |
| – | 24 | 24 | 24 | – | – | – | R77 | 27-1/4 | 7/16 | 21/32 | 1/16 | – | 29-1/2 | – | – | – | 7/16 |
| – | – | – | – | 24 | – | – | R78 | 27-1/4 | 5/8 | 1-1/16 | 3/32 | – | – | 30-3/8 | – | – | 5/8 |
| – | – | – | – | – | 24 | – | R79 | 27-1/4 | 13/16 | 1-7/16 | 3/32 | – | – | – | 31-1/4 | – | 13/16 |
| Threaded, Socket-Welding, Slip-On, Lap Joint, and Blind | Weld Neck | |||||
| Outside Diameter (1) | when the O.D. is 24″ or less | ±1/16″ | Outside Diameter (1) | when the O.D. is 24″ or less | ±1/16″ | |
| when the O.D. is over 24″ | ±1/8″ | when the O.D. is over 24″ | ±1/8″ | |||
| Inside Diameter | Threaded | within limits on boring gauge | Inside Diameter | = 10″ | ±1/32″ | |
| Socket-Welding, Slip-On and Lap-Joint | = 10″+1/32″, -0″ =12″+1/16″,-0″ | 12″ through 18″ | ±1/16″ | |||
| = 20″ | +1/8″, -1/16″ | |||||
| Outside Diameter of Hub (1) | = 12″ | +3/32″, -1/16″ | Diameter of Contact Face | 1/16″ Raised Face | ±1/32″ | |
| = 14″ | ±1/8″ | 1/4″ Raised Face Tongue & Groove Male, Famale | ±1/64″ | |||
| Diameter of Contact Face | 1/16″ Raised Face | ±1/32″ | Diameter of Hub at Base (1) | when Hub Base is 24″ or less | +1/16″ | |
| 1/4″ Raised Face Tongue & Groove Male, Famale | ±1/64″ | when Hub Base is over 24″ | ±1/8″ | |||
| Diameter of Counterbore | Same as for Inside Diameter | Diameter of Hub at Point of Welding | NPS = 5″ | +3/32″, -1/32″ | ||
| NPS = 6″ | +5/32″. -1/32″ | |||||
| Drilling | Bolt Circle | ±1/16″ | Drilling | Bolt Circle | ±1/16″ | |
| Bolt Hole Spacing | ±1/32″ | Bolt Hole Spacing | ±1/32″ | |||
| Concentricity of Bolt Circle with Respect to Facing | NPS = 2 1/2″, 1/32″ max | Concentricity of Bolt Circle with Respect to Facing | NPS = 2 1/2″ 1/32″ max | |||
| NPS = 3″, 1/16″ max | NPS = 3″ 1/16″ max | |||||
| Thickness | = 18″ | +1/8″, -0″ | Thickness | = 18″ | +1/8″, -0″ | |
| = 20″ | +3/16″,-0″ | = 20″ | +3/16″,-0″ | |||
| Length Through the Hub (1) | = 18″ | +1/8″, -1/32″ | Length Through the Hub | NPS = 4″ | ±1/16″ | |
| 5 = NPS = 10″ | +1/16″, -1/8 | |||||
| = 20″ | +3/16″, -1/16″ | = 12″ | +1/8″, -3/16 | |||
Frequently Asked Questions
- What is an RTJ ring gasket number?
- R-series ring gaskets for ASME B16.5 ring type joint flanges are numbered R11 to R79. The number sets the ring's pitch diameter and cross-section, and each flange size and pressure class takes one ring number. For example, a 4 inch Class 150 RTJ flange takes an R36 ring, while 4 inch Class 300 and 600 take an R37.
- How do I find the ring number for my flange?
- Pick the pressure class and nominal size above. If the flange is unmarked, measure the groove pitch diameter (center of the groove on one side to the center on the other side) and the groove width, then use the measured groove mode.
- What is the difference between oval and octagonal ring gaskets?
- Both are R-series ring joint gaskets with the same ring numbers. An oval ring has a rounded cross-section; an octagonal ring has flat angled faces. Use the style your piping specification calls for.
- Can I reuse an RTJ ring gasket?
- Ring joint gaskets are designed to deform slightly into the groove when the joint is tightened, so they are normally replaced each time the joint is opened.
- Do RTJ flanges need longer studs?
- Yes. Ring type joint flanges need longer studs than raised face flanges because of the gap the ring leaves between the flanges. The Texas Flange bolt and stud chart lists both lengths.
